Dear screen players, please pay attention! The topic we are going to talk about today is the most crazy question when installing LED screens——​ ​Where is the HDMI interface hidden?​​? Do you often encounter problems when plugging in wires and squatting behind the screen and sweating profusely? Don’t panic. After reading this article, you will be sure to avoid half of the detours when installing it next time!

1. Three major hiding places for HDMI interface

​​1. "Mechanical Door on the Back of the Box"​​
The HDMI interface of most LED screens is like a master of hide and seek, and they love to hide on the back of the display. Find out if there is any metal panel with dust-proof cover. This design not only protects the interface but also facilitates maintenance. To give a real case: When installing an advertising screen in a shopping mall last year, the installer searched for 20 minutes before finding the interface hidden in the folding cover in the lower right corner!

Here is a tip:​​The interface area of the outdoor screen usually has a waterproof rubber ring​​, it has a rubbery texture to the touch； The indoor screen is mostly made of magnetic flap cover, which can be opened with a light buckle. If you encounter an area with a heat dissipation hole, it will definitely be an interface concentration camp!

​​2. "Invisibility Technique in the Stitch Seam"​​
The popular ultra-thin LED screen now plays with high technology, and directly hides the HDMI interface at the module splicing. When encountering this design, remember the formula:​ ​"Press the four corners and push the middle"​​——There are hidden buckles at the four corners, and the interface panel can be popped up by nudged in the middle. According to actual test data, this hidden design can reduce the screen thickness by 30%, but it takes an average of 15 minutes for novices to find interfaces!

​​3. "Cloud control of smart modules"​​
High-end LED screens are even more amazing, so you don’t need to find a physical interface at all! It can be achieved through mobile APP​ ​Wireless HDMI signal transmission​​. The smart screen installed for an e-sports hall last year directly transmitted 4K/120Hz signals through the 5G network, saving 80% of the wiring time. However, it should be noted that wireless transmission requires high network environment and may become PPT when the network speed is less than 100Mbps!

2. Three golden rules for selecting interface locations

​​1. Principle of heat dissipation​​
Never install the HDMI port directly under the heat sink! Temperature exceeding 60℃ will cause signal attenuation, and actual measured data shows that the transmission distance will be shortened by 40% in high-temperature environments. It is recommended to install it at the diagonal position of the heat dissipation hole to leave at least 10cm of heat dissipation space.

​​2. The principle of wiring convenience​​
Remember this formula:​ ​Optimal installation height = bottom edge of the screen + 30cm​​. This height can not only hide cables, but also facilitate squatting and plugging. There is a reverse textbook: a certain exhibition hall installed the interface at a 2-meter high position, and every time you debug, you have to set up a ladder, and cut it in half the efficiency!

​​3. Three elements of signal stability​​

• ​​Distance control​​: The transmission line should not exceed 15 meters, and a repeater should be added to the long distance.
• ​​Avoid interference​​: Stay away from the power cord at least 20cm, and be 90 degrees a right angle when crossing
• ​​Interface orientation​​: The outdoor screen interface is installed facing down to prevent rainwater from pouring back (don’t laugh, there have been tragedies in which the interface is filled with water and burning the motherboard)

3. Installation practical pit avoidance guide

​​The five must-see for beginners​​
✅ You need to prepare a USB interface detector (30 yuan can save lives)
✅ Use HDMI2.1 cable with shielding (identify the 48Gbps mark)
✅ You must first turn off the power and then plug it out (a bloody lesson: three graphics cards are burned when the power is operated)
✅ Leave room for maintenance for the interface area (at least one punch distance)
✅ Use a cable ties to secure the cable (to prevent poor contact caused by pulling)

❌ Do not use adapters to connect old equipment (signal loss up to 50%)
❌ Do not plug in multiple devices with stacked Arhat style (more than 3 will grab bandwidth)
❌ Do not ignore the ground wire (static accumulation may break down the chip)
❌ Do not forcefully bending the wire (minimum bending radius ≥5cm)
❌ Do not use alcohol to wipe the interface (which will corrode the gold plating layer)

Personal experience of trapping

After eight years of working in the display project, my deepest experience is:​​Good interface is not as good as good planning​​! Last year, I installed a stage floor tiled screen for the music festival and specially designed the HDMI interface in the side maintenance compartment, but six interfaces were broken during the performance. Later it was changed to the top hidden type, and the failure rate was directly reset to zero.

There is another cold knowledge:​​Interface color will affect heat dissipation​​! The black interface absorbs heat by 20℃ more than the silver, so try to choose the silver-white interface area for outdoor screens. Recently, I am testing graphene heat dissipation patches, which can directly reduce the interface temperature by 15℃. I will share with you when the test is mature.

Finally, I would like to say my heart: If you can’t find the interface, don’t force it! Remember to read the manual first, or contact the manufacturer's technical support directly - leave the professional matters to professionals, and the time saved is enough for you to take three more orders in your business!

for more product information and pricing, please contact us .